• Home
• NEWS
• Products
  • Dewar Flasks
  • Cryo Vessels
  • Cold Traps
  • Kaltgas System
  • Waste Disposal Tank
  • Tempering Beakers
  • Reaction Vessels
    • not heatable
    • heatable with GL18
    • heatable with DN15
    • Lids
    • Supporting Frames
    • Accessories
    • Assemblies
    • Configuration Wizzard
  • Columns
  • Cryostats LN2/LHe
  • Thermal Protection
    for Data Logs
  • Large Insulation Box
  • NLK Apparatur
    mit Dewar
  • Customers Glass Vessels 
• Downloads
• Order Catalog
• About Us
• Dealers&Agencies 
• Contact/Imprint
• General Terms

Accessories For Reaction Vessels

• Thermal Jacket Joint
• Silicone O-rings
• Quick Release Clamps
• Double Holder "Vario-Grip"
• Supporting Devices
• Stirrers
• Coupling For Stirrers
• Stirrer Seals
• Metal Hoses
• Bottom Outlet Valves

Thermal Jacket Joint

The thermal jacket joint is available in three versions:

• Threaded Glass Joint GL18
  
  with plastic olive (PGT/PTFE) for hoses with an internal diameter of 10mm.
  Internal diameter of olive is 7mm.
  
  Temperature Range: -10°C to max. +120°C
  
  

  Plastic olive straight	Article No. 4044
  Plastic olive angled	Article No. 4044/A

• DN15 Glass Flange: Accessories
  
  
  

  Metal adapter for thermostat hoses (DN15 to M16x1)	Article No. 4200
  Silicone sealant DN15 / Temperature range –40°C to +150°C	Article No. 4201
  PTFE sealant DN15 / Temperature range –180°C to +220°C	Article No. 4202
  Graphite sealant DN15 / for very high temperature +300°C	Article No. 4203

• DN25 Glass Flange: Accessories
  
  
  

  Metal adapter for thermostat hoses (DN25 to M16x1)	Article No. 4205
  Silicone sealant DN25 / Temperature range –40°C to +150°C	Article No. 4206
  PTFE sealant DN25 / Temperature range –180°C to +220°C	Article No. 4207
  Graphite sealant DN25 / for very high temperature +300°C	Article No. 4208

Silicone O-rings

Silicone O-rings, FEP Covered, Seamless

Quick Release Clamp Made Of Stainless Steel

Quick Release Clamp Made Of Stainless Steel With Two Supporting Rods

Double Holder "Vario-Grip"

This holder allows to remove the lid or vessel from the holder or the set-up without dismounting the set-up. The supporting rods can be utilised vertically or horizontally.

Universal Supporting Device Made Of Stainless Steel

massive version fror installation in a rod frame.

Supporting Device

massive version fro installation in supporting frame, thickness supporting frame: standard 27mm, on request 13mm or 30mm

---------------

Stirrer Out of Glass and Stainless Steel

Following specifications are needed (please have a look at general drawing and example):

1. Type of stirrer
   • Anchor stirrer with two arms: Article No. = AZ
   • Anchor stirrer with four arms: Article No. = AV
   • Propeller stirrer with three blades: Article No. = PD
   • Propeller stirrer with four blades: Article No. = PV
   • Second stage, marked with additional Z: Article No. = **Z
   • 
     Type AZ
   • 
     Type PV
   • 
     Type PVZ
2. Shaft Diameter
   • 8 mm: Article No. = W8
   • 10 mm: Article No. = W10
   • 16 mm: Article No. = W16
3. Material
   • Glass: Article No. = G
   • V4A: Article No. = V
   • V4A: PFA coated: Article No. = PFA
4. Type Of Reactor
   • Article No. = TRGN****
   • or inner height of reactor and flange size
5. Type Of Lid
   • Article No. = D****
   • or total height of lid
6. Used Stirrer Seal
   • Article No. = Art.No. of stirrer seal
   • Type or article number

Example:

Art.No.: PVZ - W16 - V - TRGN7197 - D4303 - 40466

1. propeller stirrer with four blades and second stage = PVZ
2. 16mm shaft = W16
3. out of V4A = V
4. for reactor type TRGN7197 = TRGN7197
5. lid type D4303 = D4303
6. stirrer seal type RV 16/45 = 40466

Stirrer out of V2A, PTFE coated

Following specifications are needed (please have a look at general drawing and example):

1. Type of stirrer
   • Anchor stirrer with two arms: Article No. = AZ
   • Anchor stirrer with four arms: Article No. = AV
   • Propeller stirrer with three blades: Article No. = PD
   • Propeller stirrer with four blades: Article No. = PV
   • Second stage, marked with additional Z: Article No. = **Z
   • 
     Type AZ
   • 
     Type PV
   • 
     Type PVZ
2. Shaft Diameter
   • 8 mm: Article No. = W8
   • 10 mm: Article No. = W10
   • 16 mm: Article No. = W16
   Following typed are available (shaft diameter to flange size):
   
   

   Type of stirrer	Ø NW60	Ø NW100	Ø NW120	Ø NW150	Ø NW200
   AZ	8	8 & 10	8 & 10	10 & 16	16
   PZ	8	8 & 10	8 & 10	10 & 16	16
   PD	8	8 & 10	8 & 10	10 & 16	10 &16
   PV	8	8 & 10	10	10 & 16	10 &16

3. Material
   • Article No. = B
4. Type Of Reactor
   • Article No. = TRGN****
   • or inner height of reactor and flange size
5. Type Of Lid
   • Article No. = D****
   • or total height of lid
6. Used Stirrer Seal
   • Article No. = Art.No. of stirrer seal
   • Type or article number

Example:

Art.No.: AZ - W8 - B - TRGN7168 - D4201 - 40451

1. anchor stirrer with two arms = AZ
2. 8mm shaft = W8
3. out of V4A (PTFE coated) = B
4. for reactor type TRGN7168 = TRGN7168
5. lid type D4201 = D4201
6. stirrer seal type Typ RVFE 8/29 = 40451

Coupling For Stirrers

Stirring couplings (stainless steel) are used to compensate any vibrations between stirrer and stirring tools

Stirrer Couplings with Headless Pins

for high torques; out of stainless steel

Couplings For Stirrers With Cardan

Magnetic Stirrer Seals

vacuum and magnetic stirrer-seal coupling out of stainless steel 1.4401 CrNiMo, with permanent magnets, absolutely gas- and vacuum-tight, for vacuum use, resistant against most acids and alkalines rot. 2.500 U/min.

Stirrer Seals Out of Glass

The KGW dynamic stirrer seal is suitable for both vacuum and excess pressure areas. It has two separate PTFE seals which can be adapted for excess and vacuum applications by altering of their mounting direction.

PTFE-Stirrer Seals

for PTFE-coated V2A stirrers

Metal Hoses

thermally insulated, with M16x1 threaded joints on both sides, matches to standard threads of circulation thermostats, max. operating temperature +300° C.

Bottom outlet valve

The bottom-outlet is available in three versions.

• Industrial valve "J" (linear closing)
  The industrial valve is a dead volume free PTFE spindle valve with sloped outlet. The spindle shall be pressed in without turning. In the valve housing is an additional spring mounted in. So the spring pressure of the spindle to the valve seat can be increased spring- loaded and the spindle regulates herself. This guarantees a good tightness at large variations of temperature. The industrial valve is available with a 10 mm bore-hole (standard) and as desired with a 20 mm bore-hole.
  
• Laboratory valve "L"
  The laboratory valve is a dead volume free PTFE spindle valve with the spindle being pressed in while turning. The valve has an 10 mm bore-hole.
  

© 2003-2011 KGW-Isotherm. All Rights Reserved.